G-Xpc Spraygun #9600-G

Please note* Fuji spray guns can only be used with an HVLP Turbine (any make). They cannot be used with standard compressors.

Because of the popularity of this spraygun, some dealers are making this spraygun available with all Fuji systems. Please check with the retailer when purchasing your system and ensure that you are using the correct part number.

Fuji Spray® developed this spraygun to meet the rising demand for a gravity gun that can be used with any HVLP turbine. The Gravity Spraygun has all the features of the standard Fuji Xpc gun including the Pattern Control Knob to adjust the size of the fan. The GT-X2 comes with the #4 Aircap installed. This is the medium output size, best for fine finishing with lacquers, enamels, polyurethanes, latex, water based coatings and more. The Gravity Cup is 400cc (.85 Pint).

**NEW** The cup now uses pressure feed (plus gravity) for faster coverage. It now has the same abilities as our Xpc spraygun. This spraygun is already proving to be very popular with Bathtub and Auto Refinishers but it is also perfect for cabinet spraying too. Also, please see the 7015 Upper Hose Connector Kit for those who prefer the hose attached to the rear of the barrel.

Cleaning is a snap! The gun does not have to be connected to the hose or turbine. Here’s how…

• Partially fill the cup with solvent
• Wind out the fluid knob and pull the trigger
• Direct the fluid stream into a container

An excellent choice for professional use or even for the serious hobbyist. Sorry... Fuji only manufactures this spraygun with the 400cc size cup.

Mini 3-Cup Set #9080

Complete 1/2pint (8ozs) miniature cup assembly. Supplied with 2 extra cups and 3 heavy-duty lids equipped with gaskets. This assembly is lightweight taking weight off the wrist. The small size allows access into confined areas such as cabinets, bookshelves etc. The cup is pressurized so the spray pattern is always perfect. You will think of many uses for these cups - storing paints and stains. It's great for quick color changes. Any type of touch-up work. Guitar makers and auto touchup are just 2 areas where this cup assembly is proving to be popular. if you are always spraying larger pieces such as kitchen cabinets, this cup set is too small for you - it would require too many fill ups to make it practical. Please note* this cup assembly can only be used with the 9600-4 spraygun. It cannot be fitted to the Fuji Gravity Guns.

Flexible Whip Hose #2049F

Lightweight 6ft. hose is highly flexible. Couplings are made from a glass fiber-reinforced polymer. Takes weight off the wrist and the flexibility allows for effortless maneuverability of the spraygun. An added feature is that the air through the spraygun is not as hot (due to the fact the spraygun is now 6ft further from the turbine). This often alleviates problems with fast drying lacquers (and Latex House Paint) drying too quickly. This Whip Hose features a smooth internal bore. Please note* this hose cannot be connected to the turbine - it is an extension hose and must only be connected to the end of the standard 25ft hose.

Extension Hose #7011

Heavy-duty 8ft. extension hose is added between the turbine and the main (25ft) hose. This greater length results in much cooler air (approx. 20 degrees cooler) passing through the spraygun. This alleviates problems with fast drying lacquers and latex drying too quickly. No difference will be noticed in pressure or volume of air.

SPARE PARTS

Caps for Cups # 9903-3

Set of 3 plastic lids will fit any Fuji 1qt (1000cc) cup. Handy for storing paints. Inexpensive.

AIRCAP SETS - COLOR CODED - Please note** the Aircap Sets shown below can only be used with the new Xpc Sprayguns. If you own an older XT or GT-X, please check the part numbers in your User Manual (9001).

8050-2 Aircap Set #2H

For Artists, very fine work, small surfaces, touch up, shading. STAINS, THINNER, ZINC, SPRAYTAN SOLUTION. .7mm (0.25") VERY FINE OUTPUT. FOR Xpc SPRAY GUN ONLY.

8050-3 Aircap Set #3H

Most 'fine-finishing'. WATER-BASED/BORNE LACQUERS, SEALERS, CELLULOSE, ACRYLICS, SYNTHETICS, POLYURETHANE, STAINS, VARNISH, GLITTER PAINTS, PRIMERS. 1mm (.039") FINE TO MEDIUM OUTPUT. FOR Xpc SPRAY GUN ONLY.

8050-4 Aircap Set #4H

Standard size setup in our Xpc spray gun. Similar to No. 3 but more coverage. Especially suitable for AUTOMOTIVE ENAMELS, NITROCELLULOSE LACQUERS, CATALYZED LACQUERS and LATEX (EMULSION) where finer finish is required such as louver doors, trim, cabinets (see section above about Latex). Also good for VARNISHES and OIL-BASED PAINTS, POLYURETHANES, ETC. 1.4mm (.055") MEDIUM OUTPUT. FOR Xpc SPRAY GUN ONLY.

8050-5 Aircap Set #5H

Larger surfaces, thick layers, spotted effects. SEALERS, VARNISH,  POLYURETHANE, OIL BASE PAINTS, ENAMELS, EPOXY, PLASTIC, ADHESIVES, FLOOR PAVING PAINTS, LATEX (on walls) SPLATTER PAINTS, MULTI-FLECK ETC. 1.8mm (.070") MEDIUM OUTPUT. FOR Xpc SPRAY GUN ONLY.

8050-6 Aircap Set #6H

Very heavy flows, fast coverage. STONE FINISH PAINTS, TEXTURE  COATING, INDUSTRIAL PRIMERS, LATEX (on walls, ceilings), EMULSION ETC. 2.2mm (.086") MEDIUM OUTPUT. FOR Xpc SPRAY GUN ONLY.

2039 - Cup Parts Kit

Kit includes wearable parts that you should always have on hand. Older Fuji cups with the black-colored lid can be converted to use the 2038 Plastic Diaphragm. If you haven't upgraded yet, we recommend you do so. We have found that using this diaphragm in combination with the 2024 pressure tube/check valve, there is very little chance of the paint backup. To use the diaphragm, the older 2036 gaskets are too thick so they must be exchanged for the new 2037 Thin gasket. All the parts shown in the kit can be ordered separately (please see below). This diaphragm is very effective at preventing paint entering the clear pressure tube.

2024-5 Pressure Tube/Check valves

Pressure tubes with check valves installed. Available only in packs of 5. These tubes fit older Fuji sprayguns. If clogged, checkvalve cannot be taken apart but they can be soaked in thinner for up to 30 minutes to free any blockage. 2036-5 Cup Gaskets

The diaphragm 2038 must be used with these gaskets. Available only in packs of 5.

2038 - Plastic Diaphragms

Tough and durable, the diaphragms should last months (if not years) if care is taken sliding them down the metal fluid tube. To remove them from the cup, grab the tab. The air hole in the diaphragm should be positioned at the rear of the cup (towards the handle). That is, unless you intend spraying upwards for any length of time. For spraying upwards, position the hole in the diaphragm towards the front of the spraygun. The idea is to keep the hole out of the paint as much as possible. These diaphragms, in combination with the pressure tube/check valve, cure the problem of paint backing up the pressure tube.

9044 Paint Strainer

Inexpensive nylon strainer fits at the end of the metal fluid tube. Durable and long-lasting. Can be soaked in thinner to clean. Sold in packs of 2.

4009-2 Mini-Mite Turbine Filters

Turbine filters fit all Mini-Mite™ Model Turbines. Coarse filter goes on the right hand side (as seen when looking at the front of the case) fine filter on the left. Please note* these filters will not fit the Super Model. Please order 2044-2 for the Super.

5029 Q-Turbine Filter

Turbine filter fits all Q-Series turbines. Always ensure that upon installation, the filter fills the whole filter enclosure. Use something like a screwdriver to lever the filter into position. Please note* the turbine does not have to be taken apart to remove or replace the filter. This filter is a friction fit – it can be replaced in seconds.

Recommended Reading/Video

The Hand-Applied Finishes DVD Video - Combines two videos from Jeff Jewitt, Coloring Wood and Applying Topcoats that were originally released as separate tapes as a companion to Hand Applied Finishes in 1997. Applying Topcoats won the Golden Hammer that year for Best How-To Video. In this 80 minute jam-packed DVD you will learn the complete finishing process, from preparing the wood to rubbing out the finish and doing minor repairs. Learn how to French Polish, use stains and glazes, brush different finishes and much more.

Spray Finishing Made Simple - NEW!

Jeff Jewitt's latest and much anticipated release by the Taunton Press (publisher of Fine Woodworking Magazine). This project is a new concept in book publishing combining a feature and technique packed 45 minute DVD with a 125 page companion book.

In the book and DVD, Jeff explains how to choose Equipment, how to set it up and demystifies the entier spray-finishing process. Through this unique multimedia approach, which includes detailed step-by-step instructions, photos, and how-to video, readers learn where to safely spray finishes and how to troubleshoot and solve spray finishing problems. Both the book and the DVD cover a variety of spray systems, solvents and waterborne finishing products.

Understanding Wood Finishing - Available in Paperback
We have never endorsed a book before but this one is so good, we heartily recommend it to anyone. The Author, Bob Flexner has been finishing wood for more than 20 years. Bob spent 6 years learning the chemistry of finishing and has distilled this technical knowledge into practical information. Bob clears up confusion by debunking many myths about finishing. Beautifully illustrated and a pleasure to read. A perfect addition to your library ! A Rodale Press Book.


Great Wood Finishes - Available in Paperback
An excellent book we would like you to know about. This is written by Jeff Jewitt, an author you may be familiar with from his previous book Applied Finishes. Detailed step-by-step instructions lead you through each technique with over 400 illustrations. Spraying is well covered. A Taunton Press Book. Please note: We do not actually sell books - please check with your local tool store or bookstore.
 

Complete Illustrated Guide to  Finishing - Another great book by Jeff Jewitt. The "Complete Illustrated Guide to Finishing" is his latest release from the Taunton Press. This hardcover book has over 300 pages and 800 color photos and is the most up-to-date, comprehensive book on finishing wood ever published. This book covers both tried and true techniques like French Polishing right alongside more modern techniques such as spraying polyester and conversion varnish. You'll learn about all the latest products and the tools to apply them, and techniques like toning, shading, sun-bursting, creative grain filling, and applying finishes, both by hand as well as spray. The book is organized for quick access which makes it easy to find each technique or topic.